Search found 243 matches

by woodae
Mon Mar 17, 2008 5:14 pm
Forum: Engine/Intake/Exhaust
Topic: whoa smoke from under passenger seat,
Replies: 3
Views: 391

my floor got wet and melted a connector it was one of the two white ones just before the ecu i was wondering what is the best way to find out what those wires were for
by woodae
Mon Mar 17, 2008 4:37 pm
Forum: Engine/Intake/Exhaust
Topic: bosch injectors
Replies: 1
Views: 299

bosch injectors

a while back i bought bosch injectors for my 1.5l lanos from injectors online, i was wondering if those will work in a 2.0l i have a 96 jetta and i was wondering if they will work in that because you said the flow rate was a little bit higher
by woodae
Mon Mar 17, 2008 4:34 pm
Forum: Engine/Intake/Exhaust
Topic: whoa smoke from under passenger seat,
Replies: 3
Views: 391

whoa smoke from under passenger seat,

i am taking the seat out now to see
by woodae
Mon Feb 11, 2008 11:22 pm
Forum: Engine/Intake/Exhaust
Topic: new o2 sensor
Replies: 7
Views: 733

so are the 1.5l and the 1'6l do they have the same o2 sensors?
by woodae
Mon Feb 11, 2008 1:49 pm
Forum: Pictures and Video Gallery
Topic: Lanos DRIFT
Replies: 7
Views: 1464

it should be "lanos spins uncontroled" its hard to have control on ice, but you can have control in starting a spin but not where u end up, one of his spins he almost goes off of the road!!!!!
by woodae
Mon Feb 11, 2008 1:34 pm
Forum: Engine/Intake/Exhaust
Topic: new o2 sensor
Replies: 7
Views: 733

i can't afford gas right now so this is a short term fix, should the oxygen sensor have a ground
by woodae
Mon Feb 11, 2008 1:31 pm
Forum: Engine/Intake/Exhaust
Topic: Hydrolocked engine.....
Replies: 12
Views: 1050

i forgot to tell the whole story, my starter blew up for some reason and when i got a second hand one, the selenoid was all rusted so i took it apart and cleaned the rust then it worked again, is the selenoid clicking when you turn the key????
by woodae
Sun Feb 10, 2008 8:07 pm
Forum: Engine/Intake/Exhaust
Topic: new o2 sensor
Replies: 7
Views: 733

i striped my new o2 sensor so i put the old one in with out hooking it up hooked up the new one and tied it to the exhaust, wrong move it was thinking it was running too hot, so i moved it to a cold place and the gas milage improved a bit and way more power, will this harm anything? i know i might b...
by woodae
Sun Feb 10, 2008 3:29 am
Forum: Engine/Intake/Exhaust
Topic: Hydrolocked engine.....
Replies: 12
Views: 1050

when i hydrolocked mine i did exactly what you said but before i did i took an air gun a blew out the cylinders from the plug oils, then i put engine fogging oil in each cylinder before i turned it over, then when i started it, i sprayed the fogging oil in the intake for a bit, before i did all of t...
by woodae
Sat Feb 09, 2008 3:18 pm
Forum: Engine/Intake/Exhaust
Topic: new o2 sensor
Replies: 7
Views: 733

yup but there is no ground on one of the wires, should there be, there was on the old one
by woodae
Fri Feb 08, 2008 2:31 pm
Forum: Engine/Intake/Exhaust
Topic: new o2 sensor
Replies: 7
Views: 733

new o2 sensor

i got a ntk o2 sensor for my car but there is no ground, there is on the casing but not on the wire, is that ok, my car is runing way different,better power in high rpm but it bogs in low rpm, i decided to finally put my ait sensor in the intake, i just had it sitting in the engine bay because there...
by woodae
Sat Feb 02, 2008 5:12 am
Forum: Holland Sport Performance
Topic: group buy! Wiseco Pistons (2.0/2.2 AND 1.6) (DOHC AND SOHC)
Replies: 60
Views: 15996

i actually have a spare set of pistons and what would these pistons do for me
by woodae
Sat Feb 02, 2008 5:05 am
Forum: Engine/Intake/Exhaust
Topic: alterator
Replies: 9
Views: 932

we did it but my bearings were different they were 6000 and 6203 the bearings u used were way bigger
by woodae
Thu Jan 31, 2008 9:37 pm
Forum: Holland Sport Performance
Topic: group buy! Wiseco Pistons (2.0/2.2 AND 1.6) (DOHC AND SOHC)
Replies: 60
Views: 15996

can u get some for a 1.5l lanos
by woodae
Fri Jan 25, 2008 6:34 pm
Forum: Engine/Intake/Exhaust
Topic: alterator
Replies: 9
Views: 932

alterator

are the bearings replaceable on a 1.5l alterator if they are can i get them from something else