install tacho on lanos?

dhd · Post by **dhd** » Sun Oct 09, 2005 6:38 pm

ubuyau wrote C refers to the position on the plug
Where each wire goes into the light blue plug,
on the plug itself there is a little molded number
to tell which one it is.

the problem is in the correct position of the wires
if u can gave as clear pis of it

and I have tested my diode and it work

dhd · Post by **dhd** » Wed Oct 26, 2005 7:56 pm

http://www.gravanatuning.com/applicatio ... ch_Adapter

can this help

AcingTeam · Post by **AcingTeam** » Thu Oct 27, 2005 12:25 am

dhd wrote:http://www.gravanatuning.com/applicatio ... ch_Adapter

can this help

You have a 1.6l, right? And you're trying to do what, install a tach? If so, you don't need any adapters, just look in the how-to section of this website and scroll all the way to the bottom. You will find SIMPLE steps on how to install a tach.

MMamdouh · Post by **MMamdouh** » Thu Oct 27, 2005 12:31 am

no... the man got a 1.5 SOHC like mine and he tried every thing to hook up the tach and the best thing he could achive is getting half signal (red lining at 3250 RPM).

MMamdouh

AcingTeam · Post by **AcingTeam** » Thu Oct 27, 2005 12:33 am

Oh I see... wasn't there someone that figured out how to do it?

MMamdouh · Post by **MMamdouh** » Thu Oct 27, 2005 12:44 am

yeah... their was this diode trick and some dual resistance setup, i know dhd tried the diod trick and it didn't work out for him.

i am going to try a different thing... i am going to harras one of my fellow woo owners and get his OEM cluster that got a tach and try it on my car, if it works fine i will buy myself a cluster with a tach... the idea of messing with ECU wiring is killing me.

MMamdouh

dhd · Post by **dhd** » Fri Nov 04, 2005 9:45 pm

thank u mmamdouh for your support

and the

is can it help me?

MMamdouh · Post by **MMamdouh** » Sat Nov 05, 2005 12:47 am

i tell you what... if the cluster swap workes out i will give you a buzz so you can do the same... i am not that expert with electronics and all.

MMamdouh

dhd · Post by **dhd** » Sun Nov 06, 2005 9:22 pm

i think it will not work coz

the cluster with a tach it came in 1.6(ecu is not the same in 1.5)
and the harness in 1.6 is not the same but the connector(for the cluster) the is same as 1.5

MMamdouh · Post by **MMamdouh** » Sun Nov 06, 2005 11:53 pm

the 1.5 did come with an OEM cluster with tach... that is the one i am going to test on my car.

MMamdouh

dhd · Post by **dhd** » Mon Nov 07, 2005 8:20 pm

i were thinking that it cam only in 1.6

MMamdouh · Post by **MMamdouh** » Mon Nov 07, 2005 9:02 pm

this is why i am hoping that the wiring and sockets will perfictly match the tach equippted cluster as i don't think "mass production" and "different harness according to accessories" concepts go together... i have also found wiring to a mid brake light that i don't have on my car and other stuff that implys that the swap is doable and will work.

it is kinda buying a car that have fog lights in its top model... the other models will have fog light holes in ther finders as well but their will be a plastic plug to cover the hole... it is much cheaper to make the same "fog light" ready fender and add in a plug for the non fog light models than to design a different bumper for each model depending on the accessory list.

MMamdouh

surfer1192 · Post by **surfer1192** » Wed Nov 09, 2005 5:25 pm

Which Tacho are u talking about the ones that comes with the car ?? or the generic ones ??

AcingTeam · Post by **AcingTeam** » Wed Nov 09, 2005 7:11 pm

surfer1192 wrote:Which Tacho are u talking about the ones that comes with the car ?? or the generic ones ??

cluster, the one that came with the speedo from factory.

MMamdouh · Post by **MMamdouh** » Tue Sep 19, 2006 12:30 pm

woo_sleeper wrote:
mmamdouh wrote:here you are:

MMamdouh
hey bro, how come i dnt have this sensor on my ride?? we both have the same car ??? wat sensor is that ???

its because that car is OBDII, it has got a cam position sensor, 2 O2 sensors and 2 CATs.

MMamdouh